How to remove and refit the front and rear Parking Brake Cable on Mercedes-Benz 190E?

In order to take off the front cable, one has to first remove the driver seat and centre console. Removal of cotter pin, clevis pin, and cable connector to the parking brake lever will be at the bottom of the lever. Pry off the grommet and hold the cable through the floorpan. The unhooking of the return spring under the vehicle and taking it off the cable swivel plate occurs below the vehicle. Unscrew the bolt that holds the rear of the front cable to the cable intermediate lever, and throw away the old bolt and put in a new one on refitting. Unscrew all the retaining clips and ties in the cable, taking note of the proper installation, and unplug it out of the vehicle. To refit, reverse the steps used to remove, ensure the cable is attached to the cable intermediate lever by fitting a new bolt and finally adjust the parking brake. In the case of the rear cable, one should start by removing the corresponding set of parking brake shoes as well as the expander mechanism on one end of the cable. Unscrew the bolt holding the outer cable to the hub carrier and pull the cable out of the back of the backplate and replace the old bolt with a new bolt during refitting. Detach the fixings and fold the exhaust heat shield out of the floorpan, then detach the return spring out of the cable swivel plate. To remove the cable by sliding out the retaining clip fixing the front end of the cable to its bracket, unhooking the cable to the equaliser plate, and accessing the cable underneath the vehicle. To refit, follow the reversal of steps to remove and when it is ready, fasten the cable to the hub with a new bolt and change the parking brake.

How to remove and install the parking brake cables on Mercedes-Benz 300TD?

Raise the vehicle and support it securely on jackstands. On some models, it may be necessary to lower the exhaust pipe for clearance, supporting it on a jackstand. Unhook the return spring, then unscrew the adjusting bolt completely and release the intermediate lever from the underbody and adjusting bracket. For the front cable, remove the cotter pin and the clevis pin securing the front cable to the intermediate lever. Pry off the spring clip securing the cable guide to the crossmember behind the transmission. Inside the vehicle, remove the trim panel for access to the cable, disconnect the inner cable from the pedal or lever, pry out the spring clip, and disconnect the outer cable. Pull the cable through the rubber grommet from under the car. Installation is the reverse of removal, adjusting the parking brake afterward. For the rear cables, disconnect the equalizer from both rear cables, pry off the spring clips, and remove the cables from the underbody brackets. Remove the parking brake shoe assemblies, take out the retaining bolts from the axleshaft housing, and withdraw the cables. Installation is the reverse of removal, and after installing the shoes, adjust the parking brake.

Genuine Mercedes-Benz Parking Brake Cable

Emergency Parking Brake Release Cable

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

86 Parking Brake Cables found

View related parts
Mercedes-Benz Parking Brake Cable
Part Number: 906-420-70-85
$46.20 MSRP: $65.00
You Save: $18.80 (29%)
ADD TO CART
Product Specifications
- Other Name: Brake Cable; Rear Cable
Fits the following Mercedes-Benz Models:
- Sprinter 3500 | 2010-2018 | Base | 4 Cyl 2.1 L DIESEL, 6 Cyl 3.0 L DIESEL
View related parts
Mercedes-Benz Release Cable
Part Number: 164-420-01-85-64
$9.46 MSRP: $13.00
You Save: $3.54 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable; Release Cable
- Replaces: 164-420-01-85
Fits the following Mercedes-Benz Models:
- R320 | 2007-2009 | Bluetec, CDI | 6 Cyl 3.0 L DIESEL
- R350 | 2006-2012 | 4Matic, Base, Bluetec 4Matic | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.5 L GAS
- R500 | 2006-2007 | Base | 8 Cyl 5.0 L GAS
- R63 AMG | 2007 | Base | 8 Cyl 6.3 L GAS
View More
View related parts
Mercedes-Benz Release Cable
Part Number: 220-420-15-85
$15.86 MSRP: $22.00
You Save: $6.14 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable
Fits the following Mercedes-Benz Models:
- CL500 | 2000-2006 | Base | 8 Cyl 5.0 L GAS
- CL55 AMG | 2001-2006 | Base | 8 Cyl 5.5 L GAS
- CL600 | 2001-2006 | Base | 12 Cyl 5.5 L GAS, 12 Cyl 5.8 L GAS
- S430 | 2000-2006 | 4Matic, Base | 8 Cyl 4.3 L GAS
- S500 | 2000-2006 | 4Matic, Base, Guard | 8 Cyl 5.0 L GAS
- S55 AMG | 2001-2006 | Base, Kompressor | 8 Cyl 5.5 L GAS
- S600 | 2001-2006 | Base | 12 Cyl 5.5 L GAS, 12 Cyl 5.8 L GAS
- SL500 | 2003-2006 | Base | 8 Cyl 5.0 L GAS
- SL55 AMG | 2003-2008 | Base, Kompressor | 8 Cyl 5.5 L GAS
- SL550 | 2011-2012, 2007-2009 | Base | 8 Cyl 5.5 L GAS
View More
View related parts
Mercedes-Benz Front Cable
Part Number: 129-420-27-85
$81.60 MSRP: $114.00
You Save: $32.40 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Line; Front Cable
Fits the following Mercedes-Benz Models:
- SL320 | 1995-1997 | Base | 6 Cyl 3.2 L GAS
- SL500 | 1995-2000 | Base | 8 Cyl 5.0 L GAS
- SL600 | 1995-2000 | Base | 12 Cyl 6.0 L GAS
View More
View related parts
Mercedes-Benz Rear Cable
Part Number: 129-420-09-85
$76.80 MSRP: $107.00
You Save: $30.20 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Cable, Brake; Rear Cable
- Replaces: 129-420-36-85
Fits the following Mercedes-Benz Models:
- SL320 | 1995-1997 | Base | 6 Cyl 3.2 L GAS
- SL500 | 1995-2002 | Base | 8 Cyl 5.0 L GAS
- SL600 | 1995-2002 | Base | 12 Cyl 6.0 L GAS
View More
View related parts
Mercedes-Benz Front Cable
Part Number: 129-420-32-85
$174.00 MSRP: $242.00
You Save: $68.00 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable
- Position: Front
Fits the following Mercedes-Benz Models:
- SL500 | 2001-2002 | Base | 8 Cyl 5.0 L GAS
- SL600 | 2001-2002 | Base | 12 Cyl 6.0 L GAS
View related parts
Mercedes-Benz Rear Cable
Part Number: 211-420-26-85-64
$48.00 MSRP: $67.00
You Save: $19.00 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable; Rear Cable
- Replaces: 211-420-20-85, 211-420-26-85
Fits the following Mercedes-Benz Models:
- E320 | 2007-2009 | Bluetec | 6 Cyl 3.0 L DIESEL
View related parts
Mercedes-Benz Release Cable
Part Number: 208-420-00-85
$4.88 MSRP: $6.75
You Save: $1.87 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable
Fits the following Mercedes-Benz Models:
- CLK320 | 1998-2003 | Base | 6 Cyl 3.2 L GAS
- CLK430 | 1999-2003 | Base | 8 Cyl 4.3 L GAS
View related parts
Mercedes-Benz Rear Cable
Part Number: 212-420-13-85
$13.42 MSRP: $18.50
You Save: $5.08 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable
- Position: Rear
- Replaces: 212-420-01-85, 212-420-12-85
Fits the following Mercedes-Benz Models:
- CLS400 | 2015-2017 | 4Matic, Base | 6 Cyl 3.0 L GAS
- CLS550 | 2012-2018 | 4Matic, Base | 8 Cyl 4.7 L GAS
- CLS63 AMG | 2012-2014 | 4Matic, Base | 8 Cyl 5.5 L GAS
- CLS63 AMG S | 2014-2018 | 4Matic | 8 Cyl 5.5 L GAS
- E250 | 2014-2016 | Bluetec, Bluetec 4Matic | 4 Cyl 2.1 L DIESEL
- E350 | 2010-2016 | 4Matic, Base, Bluetec | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
- E400 | 2013-2016 | 4Matic, Base, Hybrid | 6 Cyl 3.0 L GAS, 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV)
- E550 | 2010-2014 | 4Matic, Base | 8 Cyl 4.7 L GAS, 8 Cyl 5.5 L GAS
- E63 AMG | 2010-2015 | 4Matic, Base | 8 Cyl 5.5 L GAS, 8 Cyl 6.3 L GAS
- E63 AMG S | 2014-2016 | 4Matic | 8 Cyl 5.5 L GAS
View More
View related parts
Mercedes-Benz Release Cable
Part Number: 211-420-00-85
$15.86 MSRP: $22.00
You Save: $6.14 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable; Front Cable
Fits the following Mercedes-Benz Models:
- CLS500 | 2006 | Base | 8 Cyl 5.0 L GAS
- CLS55 AMG | 2006 | Base | 8 Cyl 5.5 L GAS
- CLS550 | 2007-2011 | Base | 8 Cyl 5.5 L GAS
- CLS63 AMG | 2007-2011 | Base | 8 Cyl 6.3 L GAS
- E320 | 2003-2009 | 4Matic, Base, Bluetec, CDI | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.2 L DIESEL, 6 Cyl 3.2 L GAS
- E350 | 2006-2009 | 4Matic, Base | 6 Cyl 3.5 L GAS
- E500 | 2003-2006 | 4Matic, Base | 8 Cyl 5.0 L GAS
- E55 AMG | 2003-2006 | Base | 8 Cyl 5.5 L GAS
- E550 | 2007-2009 | 4Matic, Base | 8 Cyl 5.5 L GAS
- E63 AMG | 2007-2009 | Base | 8 Cyl 6.3 L GAS
View More
View related parts
Mercedes-Benz Release Cable
Part Number: 203-420-04-85
$20.13 MSRP: $27.50
You Save: $7.37 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable; Release Cable
Fits the following Mercedes-Benz Models:
- C230 | 2002-2007 | Kompressor, Sport | 4 Cyl 1.8 L GAS, 4 Cyl 2.3 L GAS, 6 Cyl 2.5 L FLEX, 6 Cyl 2.5 L GAS
- C240 | 2001-2005 | 4Matic, Base | 6 Cyl 2.6 L GAS
- C280 | 2006-2007 | 4Matic, Luxury | 6 Cyl 3.0 L GAS
- C32 AMG | 2002-2004 | Base | 6 Cyl 3.2 L GAS
- C320 | 2001-2005 | 4Matic, Base | 6 Cyl 3.2 L FLEX, 6 Cyl 3.2 L GAS
- C350 | 2006-2007 | 4Matic, Luxury, Sport | 6 Cyl 3.5 L GAS
- C55 AMG | 2005-2006 | Base | 8 Cyl 5.5 L GAS
View More
View related parts
Mercedes-Benz Rear Cable
Part Number: 220-420-27-85
$66.00 MSRP: $92.00
You Save: $26.00 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable; Rear Cable
Fits the following Mercedes-Benz Models:
- CL500 | 2002-2006 | Base | 8 Cyl 5.0 L GAS
- CL55 AMG | 2002-2006 | Base | 8 Cyl 5.5 L GAS
- CL600 | 2002-2006 | Base | 12 Cyl 5.5 L GAS, 12 Cyl 5.8 L GAS
- S350 | 2006 | Base | 6 Cyl 3.7 L GAS
- S430 | 2002-2006 | 4Matic, Base | 8 Cyl 4.3 L GAS
- S500 | 2002-2006 | 4Matic, Base | 8 Cyl 5.0 L GAS
- S55 AMG | 2002-2006 | Base, Kompressor | 8 Cyl 5.5 L GAS
- S600 | 2002-2006 | Base | 12 Cyl 5.5 L GAS, 12 Cyl 5.8 L GAS
- S65 AMG | 2006 | Base | 12 Cyl 6.0 L GAS
View More
View related parts
Mercedes-Benz Rear Cable
Part Number: 171-420-01-85
$27.45 MSRP: $37.50
You Save: $10.05 (27%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable
- Position: Rear
Fits the following Mercedes-Benz Models:
- SLK280 | 2006-2008 | Base | 6 Cyl 3.0 L GAS
- SLK300 | 2009-2010 | Base | 6 Cyl 3.0 L GAS
- SLK350 | 2005-2011 | Base | 6 Cyl 3.5 L GAS
- SLK55 AMG | 2005-2010 | Base | 8 Cyl 5.5 L GAS
View More
View related parts
Mercedes-Benz Front Cable
Part Number: 203-420-09-85-64
$32.33 MSRP: $44.50
You Save: $12.17 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable; Front Cable
- Replaces: 203-420-09-85
Fits the following Mercedes-Benz Models:
- C240 | 2001-2005 | 4Matic, Base | 6 Cyl 2.6 L GAS
- C32 AMG | 2002-2004 | Base | 6 Cyl 3.2 L GAS
- C320 | 2001-2005 | 4Matic, Base | 6 Cyl 3.2 L FLEX, 6 Cyl 3.2 L GAS
View More
View related parts
Mercedes-Benz Rear Cable
Part Number: 170-420-04-85
$24.40 MSRP: $33.50
You Save: $9.10 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable
- Position: Rear
Fits the following Mercedes-Benz Models:
- SLK230 | 2001-2004 | Kompressor | 4 Cyl 2.3 L GAS
- SLK32 AMG | 2002-2004 | Base | 6 Cyl 3.2 L GAS
- SLK320 | 2001-2004 | Base | 6 Cyl 3.2 L GAS
View More
View related parts
Mercedes-Benz Rear Cable
Part Number: 210-420-15-85
$97.20 MSRP: $135.00
You Save: $37.80 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Brake Cable; Rear Cable
- Replaces: 210-420-15-85-05, 210-420-11-85
Fits the following Mercedes-Benz Models:
- E300 | 1996-1999 | Base | 6 Cyl 3.0 L DIESEL
- E320 | 1996-2003 | 4Matic, Base | 6 Cyl 3.2 L GAS
- E420 | 1997 | Base | 8 Cyl 4.2 L GAS
- E430 | 2000-2002 | 4Matic | 8 Cyl 4.3 L GAS
View More
View related parts
Mercedes-Benz Rear Cable
Part Number: 124-420-11-85
Product Specifications
- Other Name: Brake Cable
- Position: Rear
Fits the following Mercedes-Benz Models:
- 300CD | 1984-1985 | Base | 5 Cyl 3.0 L DIESEL
- 300CE | 1988-1993 | Base | 6 Cyl 3.0 L GAS, 6 Cyl 3.2 L GAS
- 300D | 1987, 1984-1985 | Base | 5 Cyl 3.0 L DIESEL, 6 Cyl 3.0 L DIESEL
- 300E | 1986-1989 | Base | 6 Cyl 3.0 L GAS
- 300SD | 1984-1985 | Base | 5 Cyl 3.0 L DIESEL
- 300SDL | 1986-1987 | Base | 6 Cyl 3.0 L DIESEL
- 300SE | 1988-1989 | Base | 6 Cyl 3.0 L GAS
- 300SEL | 1988-1989 | Base | 6 Cyl 3.0 L GAS
- 300TD | 1987, 1984-1985 | Base | 5 Cyl 3.0 L DIESEL, 6 Cyl 3.0 L DIESEL
- 300TE | 1993, 1988-1989 | 4Matic, Base | 6 Cyl 3.0 L GAS, 6 Cyl 3.2 L GAS
View More
View related parts
Mercedes-Benz Front Cable
Part Number: 163-420-02-85
Product Specifications
- Other Name: Brake Cable
- Position: Front
Fits the following Mercedes-Benz Models:
- ML320 | 1998-2003 | Base | 6 Cyl 3.2 L GAS
- ML350 | 2003-2005 | Base | 6 Cyl 3.7 L GAS
- ML430 | 1999-2001 | Base | 8 Cyl 4.3 L GAS
- ML500 | 2002-2005 | Base | 8 Cyl 5.0 L GAS
- ML55 AMG | 2000-2003 | Base | 8 Cyl 5.5 L GAS
View More
View related parts
Mercedes-Benz Rear Cable
Part Number: 164-420-23-85-64
Product Specifications
- Other Name: Brake Cable; Rear Cable
- Replaces: 164-420-03-85, 164-420-23-85
Fits the following Mercedes-Benz Models:
- GL320 | 2007-2009 | Bluetec 4Matic, CDI | 6 Cyl 3.0 L DIESEL
- GL350 | 2010-2012 | Bluetec 4Matic | 6 Cyl 3.0 L DIESEL
- GL450 | 2007-2012 | Base | 8 Cyl 4.7 L GAS
- GL550 | 2008-2012 | Base | 8 Cyl 5.5 L GAS
- ML320 | 2007-2009 | Bluetec 4Matic, CDI | 6 Cyl 3.0 L DIESEL
- ML350 | 2006-2011 | 4Matic, Base, Bluetec 4Matic | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.5 L GAS
- ML450 | 2010-2011 | Hybrid 4Matic | 6 Cyl 3.5 L FULL HYBRID EV-GAS (FHEV)
- ML500 | 2006-2007 | Base | 8 Cyl 5.0 L GAS
- ML550 | 2008-2011 | Base | 8 Cyl 5.5 L GAS
- ML63 AMG | 2007-2011 | Base | 8 Cyl 6.3 L GAS
View More
View related parts
Mercedes-Benz Rear Cable
Part Number: 220-420-28-85
Product Specifications
- Other Name: Brake Cable
- Position: Rear
Fits the following Mercedes-Benz Models:
- CL500 | 2002-2006 | Base | 8 Cyl 5.0 L GAS
- CL55 AMG | 2002-2006 | Base | 8 Cyl 5.5 L GAS
- CL600 | 2002-2006 | Base | 12 Cyl 5.5 L GAS, 12 Cyl 5.8 L GAS
- S350 | 2006 | Base | 6 Cyl 3.7 L GAS
- S430 | 2002-2006 | 4Matic, Base | 8 Cyl 4.3 L GAS
- S500 | 2002-2006 | 4Matic, Base | 8 Cyl 5.0 L GAS
- S55 AMG | 2002-2006 | Base, Kompressor | 8 Cyl 5.5 L GAS
- S600 | 2002-2006 | Base | 12 Cyl 5.5 L GAS, 12 Cyl 5.8 L GAS
- S65 AMG | 2006 | Base | 12 Cyl 6.0 L GAS
View More

| Page 1 of 5 |Next >

1-20 of 86 Results

Mercedes-Benz Parking Brake Cable

Every part of the automobile matters, and their maintenance is crucial for the health of your vehicle. Moreover, a faulted Mercedes-Benz Parking Brake Cable can impact its functionality as well as lead to system-wide problems that may endanger safety. Thus, it is imperative that one repairs or replaces failing parts for better driving experiences. Why go for OEM Mercedes-Benz Parking Brake Cables? Because they are the optimal solutions, fit your vehicle perfectly, and are easy to install. Therefore, these factors help maintain the dependability and performance of your vehicle. At MBPartsGiant.com, you may find all the required genuine parts for your Mercedes-Benz. They are delivered from authorized Mercedes-Benz dealers directly via an uncomplicated online catalog. We guarantee promptness, reliability, and cheap sales on the Mercedes-Benz Parking Brake Cable, and we always provide you with the right part at any time. Depend on our genuine Mercedes-Benz Parking Brake Cables to keep your vehicle running smoothly.

Mercedes-Benz Parking Brake Cable Parts and Q&A

Front Cable
201-420-04-85
Q: How to remove and refit the front and rear Parking Brake Cable on Mercedes-Benz 190E?
A:
In order to take off the front cable, one has to first remove the driver seat and centre console. Removal of cotter pin, clevis pin, and cable connector to the parking brake lever will be at the bottom of the lever. Pry off the grommet and hold the cable through the floorpan. The unhooking of the return spring under the vehicle and taking it off the cable swivel plate occurs below the vehicle. Unscrew the bolt that holds the rear of the front cable to the cable intermediate lever, and throw away the old bolt and put in a new one on refitting. Unscrew all the retaining clips and ties in the cable, taking note of the proper installation, and unplug it out of the vehicle. To refit, reverse the steps used to remove, ensure the cable is attached to the cable intermediate lever by fitting a new bolt and finally adjust the parking brake. In the case of the rear cable, one should start by removing the corresponding set of parking brake shoes as well as the expander mechanism on one end of the cable. Unscrew the bolt holding the outer cable to the hub carrier and pull the cable out of the back of the backplate and replace the old bolt with a new bolt during refitting. Detach the fixings and fold the exhaust heat shield out of the floorpan, then detach the return spring out of the cable swivel plate. To remove the cable by sliding out the retaining clip fixing the front end of the cable to its bracket, unhooking the cable to the equaliser plate, and accessing the cable underneath the vehicle. To refit, follow the reversal of steps to remove and when it is ready, fasten the cable to the hub with a new bolt and change the parking brake.
Rear Cable
124-420-11-85
Q: How to remove and install the parking brake cables on Mercedes-Benz 300TD?
A:
Raise the vehicle and support it securely on jackstands. On some models, it may be necessary to lower the exhaust pipe for clearance, supporting it on a jackstand. Unhook the return spring, then unscrew the adjusting bolt completely and release the intermediate lever from the underbody and adjusting bracket. For the front cable, remove the cotter pin and the clevis pin securing the front cable to the intermediate lever. Pry off the spring clip securing the cable guide to the crossmember behind the transmission. Inside the vehicle, remove the trim panel for access to the cable, disconnect the inner cable from the pedal or lever, pry out the spring clip, and disconnect the outer cable. Pull the cable through the rubber grommet from under the car. Installation is the reverse of removal, adjusting the parking brake afterward. For the rear cables, disconnect the equalizer from both rear cables, pry off the spring clips, and remove the cables from the underbody brackets. Remove the parking brake shoe assemblies, take out the retaining bolts from the axleshaft housing, and withdraw the cables. Installation is the reverse of removal, and after installing the shoes, adjust the parking brake.

Related Mercedes-Benz Parts

Browse by Model