How to remove and refit the fuel tank on Mercedes-Benz 190E?

To remove the fuel tank, always, first empty the tank by draining the remains through the filler neck using a siphon or hand pump upon normal use. Always park on a flat level area, chock the front wheels and hold the rear raised up on axle stands. Unscrew the battery negative terminal and leave it off the terminal. Removing all the hoses disconnect the fuel supply and return and vent hose and keep all the hoses labeled to be refitted later and plug in the open ends to stop leakage and dirt infiltration. The large rubber closing grommet attached to the ports of the fuel tank in the luggage compartment should be removed, the retaining clips, the carpet, and the fuel tank cover panel then released. Disconnect the wiring of the fuel gauge sender unit and loosen it out of the clips. Unscrew the fuel tank fixing nuts and access the drain hose by lifting the tank slightly and pulling out the drain hose taking note of how it is run, then unscrew the filler neck of the bodywork and retrieve sealing ring(s) and sleeves. Lift the tank to the clear, drag it back and take it out of the luggage space re-gathering any loose pieces of padding. Take out the fuel strainer in the tank unscrewing the O-ring seal of the tank and wipe out the sediment in the tank with clean fuel and again screw the fuel strainer with another O-ring seal. In case the tank has been contaminated, take out the gauge sender unit, swill it with clean fuel and in case it is very corroded or leaking repair it or replace it. Reverse the removal procedure in order to attach it again, so that all fixings are tightened to the necessary torque, padding strips are correctly laid in place, the drain hose is laid correctly and the wiring plug of the sender unit is firmly reconnected. Lastly, take the vehicle on the road and investigate fuel leakage concerning all the components that were disturbed.

How to remove and install the fuel tank on Mercedes-Benz C230?

Relieve the fuel system pressure, then disconnect the cable from the negative battery terminal. Remove the rear seat cushion and the access panels for the fuel level sensor and fuel pump/fuel level sensor module, followed by the removal of the retaining rings for both modules. Working through the access hole for the fuel level sensor, disconnect the electrical connector from the sensor assembly. Lift up the fuel level sensor from the left side of the fuel tank and siphon out as much fuel as possible, then do the same for the fuel pump/fuel level sensor from the right side. Loosen the rear wheel bolts, raise the vehicle securely on jackstands, and remove the rear wheels. Detach the two under covers by removing the nuts from the front and rear, then pull the cover straight down. Remove the entire rear exhaust system from the flange in front of the pre-muffler to the muffler/tailpipe, then remove the retaining nuts that secure the exhaust pipe heat shields and take off the heat shields. Detach the driveshaft from the rear differential flange, then remove the parking brake cable cover and disconnect the parking brake cables from the equalizer, pulling the cables out of the cable bracket. If equipped, disconnect the rear brake pad wear sensors from the calipers, trace the sensor leads, and disengage them from any clips on the rear suspension assembly before unbolting and removing the rear brake calipers, supporting them with lengths of wire. Remove the rear stabilizer bar and locate the electrical terminal for the rear wheel speed sensor leads in the underside of the vehicle body, disconnecting the two wheel speed sensor leads from the terminal. Remove the coil springs and support the rear suspension assembly with an adjustable-head transmission jack, ensuring the crossmember is securely supported on each side. Remove the four large bolts that attach the rear suspension crossmembers and carefully lower the rear suspension assembly. Remove the splash shield from the right rear wheel well, then loosen the hose clamps for the fuel filler neck hose, fuel overflow shutoff hose, and fuel tank vent hoses, disconnecting all three. Support the fuel tank, remove the fuel tank strap nuts, and detach the fuel tank straps. Lower the tank slightly and disconnect any remaining electrical harnesses and EVAP hoses before lowering and removing the fuel tank. For installation, reverse the removal process, ensuring to transfer all components from the old fuel tank to the new one if replacing it, tighten the fuel tank strap nuts securely, and adjust the parking brake cables when finished.

Genuine Mercedes-Benz Fuel Tank

Gas Tank

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

202 Fuel Tanks found

View related parts
Mercedes-Benz Tank Assembly Insulator
Part Number: 212-473-01-47-64
$219.60 MSRP: $306.00
You Save: $86.40 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Insulating Insert; Fuel Tank, Tank Assembly Insulator, Tank Insulator
- Replaces: 212-473-01-47
Fits the following Mercedes-Benz Models:
- E250 | 2014-2016 | Bluetec, Bluetec 4Matic | 4 Cyl 2.1 L DIESEL
- E350 | 2011-2013 | 4Matic, Base, Bluetec | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.5 L FLEX, 6 Cyl 3.5 L GAS
View related parts
Mercedes-Benz Fuel Tank
Part Number: 210-470-70-01
$864.00 MSRP: $1200.00
You Save: $336.00 (28%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Mercedes-Benz Models:
- E320 | 1998 | 4Matic, Base | 6 Cyl 3.2 L GAS
View related parts
Mercedes-Benz Fuel Tank
Part Number: 202-470-84-01
$1080.00 MSRP: $1500.00
You Save: $420.00 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaced by: 202-470-87-01
Fits the following Mercedes-Benz Models:
- C220 | 1994-1996 | Base | 4 Cyl 2.2 L GAS
- C230 | 1997 | Base | 4 Cyl 2.3 L GAS
- C280 | 1994-1997 | Base | 6 Cyl 2.8 L GAS
View More
View related parts
Mercedes-Benz Fuel Tank Assembly
Part Number: 213-470-07-02
$768.00 MSRP: $1070.00
You Save: $302.00 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fuel Tank; Fuel Tank Assembly
- Replaces: 213-470-17-02
Fits the following Mercedes-Benz Models:
- AMG GT 63 | 2023, 2019-2021 | Base | 8 Cyl 4.0 L GAS
- AMG GT 63 S | 2023, 2019-2021 | Base | 8 Cyl 4.0 L GAS
- AMG GT 63 S E Performance | 2023 | Base | 8 Cyl 4.0 L PLUG-IN HYBRID EV-GAS (PHEV)
- E63 AMG S | 2019-2021 | 4Matic | 8 Cyl 4.0 L GAS
View More
View related parts
Mercedes-Benz Fuel Tank
Part Number: 202-470-80-01
$984.00 MSRP: $1370.00
You Save: $386.00 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fuel Tank
- Replaced by: 202-470-88-01
Fits the following Mercedes-Benz Models:
- C230 | 1998-2000 | Base, Kompressor | 4 Cyl 2.3 L GAS
- C280 | 1998-2000 | Base | 6 Cyl 2.8 L GAS
- CLK320 | 1998-1999 | Base | 6 Cyl 3.2 L GAS
- CLK430 | 1999 | Base | 8 Cyl 4.3 L GAS
View More
View related parts
Mercedes-Benz Fuel Tank
Part Number: 253-470-82-01
$538.80 MSRP: $750.00
You Save: $211.20 (29%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Mercedes-Benz Models:
- GLC63 AMG | 2020-2021 | 4Matic | 8 Cyl 4.0 L GAS
- GLC63 AMG S | 2021 | 4Matic | 8 Cyl 4.0 L GAS
View related parts
Mercedes-Benz Fuel Tank
Part Number: 246-470-34-01
$720.00 MSRP: $1000.00
You Save: $280.00 (28%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Mercedes-Benz Models:
- CLA250 | 2014-2019 | 4Matic, Base | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS
- GLA250 | 2015-2020 | 4Matic, Base | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS
- GLA45 AMG | 2015-2019 | 4Matic | 4 Cyl 2.0 L GAS
View More
View related parts
Mercedes-Benz Fuel Tank
Part Number: 246-470-12-00
$792.00 MSRP: $1100.00
You Save: $308.00 (28%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Replaces: 246-470-48-01
Fits the following Mercedes-Benz Models:
- CLA250 | 2014-2019 | 4Matic, Base | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS
- CLA45 AMG | 2014-2019 | 4Matic | 4 Cyl 2.0 L GAS
- GLA250 | 2015-2020 | 4Matic, Base | 4 Cyl 2.0 L FLEX, 4 Cyl 2.0 L GAS
- GLA45 AMG | 2015-2019 | 4Matic | 4 Cyl 2.0 L GAS
View More
View related parts
Mercedes-Benz Fuel Tank
Part Number: 210-470-40-01
$2148.00 MSRP: $2990.00
You Save: $842.00 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fuel Tank
- Replaced by: 210-470-55-01
Fits the following Mercedes-Benz Models:
- E300 | 1996-1999 | Base | 6 Cyl 3.0 L DIESEL
- E320 | 1999, 1996-1997 | 4Matic, Base | 6 Cyl 3.2 L GAS
- E420 | 1997 | Base | 8 Cyl 4.2 L GAS
- E430 | 1999 | Base | 8 Cyl 4.3 L GAS
View More
View related parts
Mercedes-Benz Fuel Tank
Part Number: 205-470-64-02
$604.20 MSRP: $840.00
You Save: $235.80 (29%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Mercedes-Benz Models:
- C63 AMG | 2019-2021 | Base | 8 Cyl 4.0 L GAS
- C63 AMG S | 2023, 2019-2021 | Base | 8 Cyl 4.0 L GAS
View related parts
Mercedes-Benz Fuel Tank
Part Number: 247-470-21-03
$615.60 MSRP: $855.00
You Save: $239.40 (28%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Mercedes-Benz Models:
- A220 | 2019-2022 | 4Matic, Base | 4 Cyl 2.0 L GAS
- A35 AMG | 2020-2021 | 4Matic | 4 Cyl 2.0 L GAS
- CLA250 | 2020-2023 | 4Matic, Base | 4 Cyl 2.0 L GAS
- CLA35 AMG | 2020-2023 | 4Matic | 4 Cyl 2.0 L GAS
- GLA250 | 2021-2023 | 4Matic, Base | 4 Cyl 2.0 L GAS
- GLA35 AMG | 2021-2023 | 4Matic | 4 Cyl 2.0 L GAS
View More
View related parts
Mercedes-Benz Filler Neck
Part Number: 211-470-24-02
$912.00 MSRP: $1270.00
You Save: $358.00 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fuel Tank; Filler Neck
- Replaces: 211-470-34-01, 211-470-41-01, 211-470-06-02
Fits the following Mercedes-Benz Models:
- CLK350 | 2006 | Base | 6 Cyl 3.5 L GAS
- E320 | 2003-2008 | 4Matic, Base, Bluetec, CDI | 6 Cyl 3.0 L DIESEL, 6 Cyl 3.2 L DIESEL, 6 Cyl 3.2 L GAS
- E350 | 2006-2008 | 4Matic, Base | 6 Cyl 3.5 L GAS
- E500 | 2003-2006 | 4Matic, Base | 8 Cyl 5.0 L GAS
- E55 AMG | 2003-2006 | Base | 8 Cyl 5.5 L GAS
- E550 | 2007-2008 | 4Matic, Base | 8 Cyl 5.5 L GAS
- E63 AMG | 2007-2008 | Base | 8 Cyl 6.3 L GAS
View More
View related parts
Mercedes-Benz Fuel Tank
Part Number: 253-470-65-01
$1152.00 MSRP: $1600.00
You Save: $448.00 (28%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Mercedes-Benz Models:
- GLC63 AMG | 2018-2020 | 4Matic | 8 Cyl 4.0 L GAS
- GLC63 AMG S | 2018-2020 | 4Matic | 8 Cyl 4.0 L GAS
View related parts
Mercedes-Benz Fuel Tank
Part Number: 170-470-12-01
$648.00 MSRP: $900.00
You Save: $252.00 (28%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Mercedes-Benz Models:
- SLK230 | 2001 | Kompressor | 4 Cyl 2.3 L GAS
- SLK320 | 2001 | Base | 6 Cyl 3.2 L GAS
View related parts
Mercedes-Benz Fuel Tank
Part Number: 205-470-28-00
$810.00 MSRP: $1130.00
You Save: $320.00 (29%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Mercedes-Benz Models:
- C300 | 2016 | 4Matic, Base | 4 Cyl 2.0 L GAS
- C450 AMG | 2016 | 4Matic | 6 Cyl 3.0 L GAS
View related parts
Mercedes-Benz Fuel Tank Assembly
Part Number: 205-470-13-02
$653.22 MSRP: $910.00
You Save: $256.78 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Fuel Tank; Fuel Tank Assembly
Fits the following Mercedes-Benz Models:
- C300 | 2019-2023 | 4Matic, Base | 4 Cyl 2.0 L GAS, 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV)
- C43 AMG | 2023 | 4Matic | 4 Cyl 2.0 L MILD HYBRID EV-GAS (MHEV)
- E450 | 2021-2023 | 4Matic, Base | 6 Cyl 3.0 L MILD HYBRID EV-GAS (MHEV)
View More
View related parts
Mercedes-Benz Fuel Tank
Part Number: 170-470-16-01
$648.00 MSRP: $900.00
You Save: $252.00 (28%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Mercedes-Benz Models:
- SLK230 | 2001-2004 | Kompressor | 4 Cyl 2.3 L GAS
- SLK32 AMG | 2002-2004 | Base | 6 Cyl 3.2 L GAS
- SLK320 | 2001-2004 | Base | 6 Cyl 3.2 L GAS
View More
View related parts
Mercedes-Benz Fuel Tank
Part Number: 247-470-28-03
$661.20 MSRP: $920.00
You Save: $258.80 (29%)
Ships in 1-2 Business Days
ADD TO CART
Fits the following Mercedes-Benz Models:
- CLA45 AMG | 2020-2023 | 4Matic | 4 Cyl 2.0 L GAS
- GLA45 AMG | 2021-2023 | 4Matic | 4 Cyl 2.0 L GAS
View related parts
Mercedes-Benz Fuel Tank
Part Number: 202-470-88-01
Fits the following Mercedes-Benz Models:
- C230 | 1999-2000 | Kompressor | 4 Cyl 2.3 L GAS
- C280 | 1999-2000 | Base | 6 Cyl 2.8 L GAS
- CLK320 | 1998-2003 | Base | 6 Cyl 3.2 L GAS
- CLK430 | 1999-2003 | Base | 8 Cyl 4.3 L GAS
- CLK55 AMG | 2001-2002 | Base | 8 Cyl 5.5 L GAS
View More
View related parts
Mercedes-Benz Fuel Tank
Part Number: 170-470-09-01
Fits the following Mercedes-Benz Models:
- SLK230 | 1998 | Kompressor | 4 Cyl 2.3 L GAS

| Page 1 of 11 |Next >

1-20 of 202 Results

Mercedes-Benz Fuel Tank

Mercedes-Benz Fuel Tank acts as the secure reservoir that stores energy-rich fuel, prevents vapor loss, and maintains steady flow to the engine, keeping every drive smooth and efficient. Celebrated worldwide, Mercedes-Benz blends German craftsmanship with forward looking tech, offering cars, trucks, and buses that pair elegant style with innovations like MBUX voice control, energy recovery systems, and the flexible MB.OS software platform that unites driver assist, battery management, infotainment, and artificial intelligence, all designed to give drivers intuitive control, reduced emissions, and thrilling comfort. Owners appreciate swift acceleration, quiet cabins, and the confidence that comes from a brand whose heritage stretches back to 1926 and continues to pioneer digital mobility through constant research and product refinement. Equally advanced, the second mention Fuel Tank uses corrosion resistant materials, internal baffles, and integrated pumps and sensors to hold gasoline or diesel securely while actively feeding it to the powertrain and sending precise level data to the dashboard. By containing vapors inside a sealed system, it supports strict environmental standards and keeps cabin air fresh, while the lightweight yet durable case resists impact and road debris to extend life without adding unnecessary mass. Together, these design features ensure consistent fuel delivery, quieter rides, and lower emissions across the entire product lineup.

Genuine parts are built to last. These components go through tough factory testing, so you can trust they will hold up over time. At MBPartsGiant.com, finding Mercedes-Benz Fuel Tank is quick and simple. We keep a massive inventory in stock with low prices that are hard to beat. Just order online to get a real manufacturer's warranty with every single part. Returns won't be a headache either, thanks to our no-hassle policy. If you are in a rush, we provide expedited shipping to get your vehicle back on the road. Don't wait. Finish your repairs today and keep your Mercedes-Benz running like new. Explore the catalog now.

Mercedes-Benz Fuel Tank Parts and Q&A

Fuel Tank
201-470-08-01
Q: How to remove and refit the fuel tank on Mercedes-Benz 190E?
A:
To remove the fuel tank, always, first empty the tank by draining the remains through the filler neck using a siphon or hand pump upon normal use. Always park on a flat level area, chock the front wheels and hold the rear raised up on axle stands. Unscrew the battery negative terminal and leave it off the terminal. Removing all the hoses disconnect the fuel supply and return and vent hose and keep all the hoses labeled to be refitted later and plug in the open ends to stop leakage and dirt infiltration. The large rubber closing grommet attached to the ports of the fuel tank in the luggage compartment should be removed, the retaining clips, the carpet, and the fuel tank cover panel then released. Disconnect the wiring of the fuel gauge sender unit and loosen it out of the clips. Unscrew the fuel tank fixing nuts and access the drain hose by lifting the tank slightly and pulling out the drain hose taking note of how it is run, then unscrew the filler neck of the bodywork and retrieve sealing ring(s) and sleeves. Lift the tank to the clear, drag it back and take it out of the luggage space re-gathering any loose pieces of padding. Take out the fuel strainer in the tank unscrewing the O-ring seal of the tank and wipe out the sediment in the tank with clean fuel and again screw the fuel strainer with another O-ring seal. In case the tank has been contaminated, take out the gauge sender unit, swill it with clean fuel and in case it is very corroded or leaking repair it or replace it. Reverse the removal procedure in order to attach it again, so that all fixings are tightened to the necessary torque, padding strips are correctly laid in place, the drain hose is laid correctly and the wiring plug of the sender unit is firmly reconnected. Lastly, take the vehicle on the road and investigate fuel leakage concerning all the components that were disturbed.
Fuel Tank
203-470-92-01
Q: How to remove and install the fuel tank on Mercedes-Benz C230?
A:
Relieve the fuel system pressure, then disconnect the cable from the negative battery terminal. Remove the rear seat cushion and the access panels for the fuel level sensor and fuel pump/fuel level sensor module, followed by the removal of the retaining rings for both modules. Working through the access hole for the fuel level sensor, disconnect the electrical connector from the sensor assembly. Lift up the fuel level sensor from the left side of the fuel tank and siphon out as much fuel as possible, then do the same for the fuel pump/fuel level sensor from the right side. Loosen the rear wheel bolts, raise the vehicle securely on jackstands, and remove the rear wheels. Detach the two under covers by removing the nuts from the front and rear, then pull the cover straight down. Remove the entire rear exhaust system from the flange in front of the pre-muffler to the muffler/tailpipe, then remove the retaining nuts that secure the exhaust pipe heat shields and take off the heat shields. Detach the driveshaft from the rear differential flange, then remove the parking brake cable cover and disconnect the parking brake cables from the equalizer, pulling the cables out of the cable bracket. If equipped, disconnect the rear brake pad wear sensors from the calipers, trace the sensor leads, and disengage them from any clips on the rear suspension assembly before unbolting and removing the rear brake calipers, supporting them with lengths of wire. Remove the rear stabilizer bar and locate the electrical terminal for the rear wheel speed sensor leads in the underside of the vehicle body, disconnecting the two wheel speed sensor leads from the terminal. Remove the coil springs and support the rear suspension assembly with an adjustable-head transmission jack, ensuring the crossmember is securely supported on each side. Remove the four large bolts that attach the rear suspension crossmembers and carefully lower the rear suspension assembly. Remove the splash shield from the right rear wheel well, then loosen the hose clamps for the fuel filler neck hose, fuel overflow shutoff hose, and fuel tank vent hoses, disconnecting all three. Support the fuel tank, remove the fuel tank strap nuts, and detach the fuel tank straps. Lower the tank slightly and disconnect any remaining electrical harnesses and EVAP hoses before lowering and removing the fuel tank. For installation, reverse the removal process, ensuring to transfer all components from the old fuel tank to the new one if replacing it, tighten the fuel tank strap nuts securely, and adjust the parking brake cables when finished.